How to work out what wattage charger you need
Charger wattage is volts times amps, and the device chooses the profile. Read the label, match the protocol, then check what a multi-port charger shares.
Find the device maximum
The device specification lists it, usually as a wattage or as volts and amps. If it is not on the device, it is in the manual or the manufacturer's specification page. That number is the ceiling for the whole system.
Be sceptical of marketing wattage on the device side too. A phone advertised with "120W fast charging" often reaches that only with a specific proprietary charger, and falls back to a standard profile with anything else.
Match the protocol, not only the number
Two chargers can both say 65W and behave completely differently, because the wattage is the sum of what the ports can deliver across profiles. A charger that reaches 65W only on one port at a time will not give 45W and 20W simultaneously.
Check the port breakdown, not the headline figure. Multi-device use is where headline wattage misleads most often.
Buying one charger for several devices
Take the highest single device requirement as your floor, then add headroom for simultaneous use. If a laptop needs 65W and a phone needs 20W and you want both at once, a 65W total charger will not do it.
Travel chargers with folding pins and multiple ports are worth more than a slightly higher wattage you will never use, because the constraint when travelling is usually sockets, not power.
The arithmetic behind every rating
Watts are volts multiplied by amps. A charger that outputs 5V at 3A delivers 15W; 9V at 3A delivers 27W; 15V at 3A delivers 45W; 20V at 5A delivers 100W. The charger label may list several rows because USB Power Delivery negotiates among them.
The device chooses the row. A 100W charger connected to a phone that only accepts 9V/2A delivers 18W, not 100W. That is not a fault. It is the protocol working.
| Profile | Watts | Typical use |
|---|---|---|
| 5V / 2A | 10W | Basic phone charging |
| 9V / 2.22A | 20W | iPhone fast charge |
| 9V / 3A | 27W | Fast phone charging |
| 15V / 3A | 45W | Tablet or thin laptop |
| 20V / 5A | 100W | Performance laptop |
PPS and proprietary protocols
USB PD PPS lets the charger adjust voltage in small steps, which some phones use to reduce heat during fast charging. A charger without PPS can still charge a PPS phone, but may fall back to a fixed profile.
Proprietary fast-charge protocols from phone makers are a separate negotiation. A charger that supports USB PD may not support a particular proprietary protocol at full speed. Check the phone manufacturer stated charger requirement, not just the wattage.
Multi-port chargers share one budget
A 65W charger with two USB-C ports rarely gives 65W to both. The total is shared: 45W plus 20W, or 30W plus 30W, depending on the model. The label or manual states the split.
If you need full power on one laptop while charging a phone, buy a charger whose total budget is at least the laptop requirement plus the phone requirement, or use a charger with a dedicated high-power port.
A worked example: laptop plus phone
A 65W laptop and a 20W phone. A 100W charger with two USB-C ports can give 65W to the laptop and 20W to the phone, but only if the total is at least 85W and the port split supports it. A 65W charger may give 45W to the laptop when the phone is connected.
The cable to the laptop must be rated for 5A if the laptop draws 100W. For 65W, a 3A cable is enough. The phone cable can be 3A. Using a 100W charger does not force 100W into either device; the devices request what they can accept.
Read the charger port table before buying. The headline wattage is a maximum, not a promise for every port at once. If the table is not published, assume the total is shared and the laptop will drop when the second port is used.
Leave headroom. A charger running at 100% of its rating for hours will run hotter and may derate. A 100W charger for an 85W load is a more comfortable match than a 90W charger for the same load.
- Add the device maximums
- Leave 15–20% headroom
- Check the per-port split
- Match cable current to the port
- Use the high-power port for the laptop
What to write down before you shop
Write down three numbers: the device maximum in watts, the number of devices you want to charge at once, and the current rating of the cable you already own. The charger has to cover the first two; the cable has to cover the charger output.
For a laptop, the original charger or the USB-C input rating gives the maximum. For a phone, the manufacturer fast-charge page is more reliable than the box, because the same phone can ship with different chargers in different markets.
Add the numbers, leave headroom, then look for a charger whose port table matches. A 100W charger with a 65W plus 30W split covers a laptop and a phone; a 100W charger with one 100W port covers the laptop but not the phone at full speed.
Charging and power Browse the Dynamic8 range for this topic.Related reading
- GaN charger vs standard charger: what changes in practice
- Why your USB-C cable charges slowly (and how to check)
Frequently asked questions
Is a higher wattage charger bad for my phone?
No. A USB Power Delivery device negotiates the profile it wants and will not draw more than it asks for. A 100W charger does not force 100W into a phone that requests 20W.
Can I charge a laptop with a phone charger?
Sometimes, slowly. If both support USB Power Delivery, the laptop will charge at the charger's maximum, which may be below what the laptop needs to run and charge at the same time. Many laptops will draw down the battery while running on a low-wattage charger.
Why does my charger get slower with two devices plugged in?
The total wattage is shared across ports. Plugging in a second device often reduces what the first port can deliver, so each device may fall back to a slower profile.
Is a higher-wattage charger safe for my phone?
Yes, if it is a reputable USB PD charger. The phone requests the profile it supports. The charger does not push more power than the device asks for.
What wattage do I need for a laptop?
Check the original charger or the laptop USB-C input rating. A 45W laptop needs at least 45W. A 100W laptop needs a 100W charger and an e-marked 5A cable.